Select your store for Click & Collect*
Find your nearest store
Change postcode

As they reduce the risk of damage caused to systems by tenants failing to bleed air from radiators, as well as the cost of call-outs from those tenants who call out service engineers when air builds in a radiator.
Often systems have a problem radiator in which air collects; most often the towel rail. The symptoms are a cold top bar and the noise of bubbling water. The correct Aladdin product (check the thread size of the radiator) can be installed without draining the system. Just shut off the two water valves, release the pressure in the radiator via the existing manual vent, and use a spanner to take out either the manual vent or the blanking plug before installing the Aladdin valve. Open the water valves and the radiator will then bleed itself.
An increasing number of professionals believe Aladdin’s Hygroseal™ products more than pay for themselves in time-saved in new installations. The installation of new or replacement radiators traditionally has required the time consuming task of running from radiator to radiator to bleed air out as the system refills. Further, water out of the tap contains about 17% air by volume which separates naturally within the system over time and, in a system without Aladdin’s valves, would necessitate the regular bleeding of radiators for the first two weeks of operation at least. Some installers now fit Aladdin’s products on every radiator they fit to save time and money.

With a 1/2" BSP thread, the threaded hole in the tapping at the top of the radiator is approximately 20mm diameter - you should be able to fit your index finger in the tapping. The plug screwed in to the tapping will either be a chrome hexagonal valve, or a 'plug' with a square cavity in it. If you are uncertain or for smaller tappings please contact your radiator's manufacturer.
Yes, on newly installed closed systems there will be a small pressure drop over the first 2 weeks or so as dissolved air separates from the fresh water (around 17% by volume), but any further pressure drop would be due to loss of system water (leaks). Some installers are priming a newly installed system to about 10% more than its operating pressure to compensate on a system fitted with Autovents.
The first time radiators fitted with these Hygroscopic™ Autovents are filled the air hisses out until water hits the hygroscopic washers and then they seal (you will often see a small 'bubble' of water after the first fill). If more air/gas builds up in the radiator, it will not escape until the hygroscopic washers have dried a little and have shrunk enough for gas/air to escape. The time it takes for the hygroscopic washers to dry and shrink varies according to ambient temperature and humidity: see the table in the Technical Details on the Product Page. So please, give this valve time to dry, before contacting us.
Yes. Cartridge version: by loosening the cartridge slowly until you can hear gas/air escaping. Cartridge-free version: by using a spanner to loosen the whole valve slowly until you can hear gas/air escaping.
If after a minimum of 5 years, the radiator starts getting cold at the top, the cartridge may require replacing in order to continue venting automatically. It is worth manually venting in case it is simply a case of the radiator running cool for a long period, and then seeing if the valve starts venting automatically again.
Yes, provided the temperature of the piping allows the valve to operate at 35°C for the Hygroseal vent.
Yes, on newly installed closed systems there will be a small pressure drop over the first 2 weeks or so as dissolved air separates from the fresh water (around 17% by volume) , but any further pressure drop would be due to loss of system water (leaks). Some installers are priming a newly installed system to about 10% more than its operating pressure to compensate on a system fitted with Autovents.
The answer is linked to the above - continual venting will be due to new air entering the system (through micro-gaps in joints etc.). Once the fresh water has vented its 17% of absorbed air the volume of water cannot further reduce in size - so if you still experience pressure drop it's due to water loss, i.e. a leak, which will require to be cured.
On about 1 in 400 systems air may be drawn in to the system where either (a) there is a radiator close to the suction side of the pump or, (b) where a radiator is higher than the water tank, in which case when the pump stops running a vacuum forms (e.g. in loft conversions).The Hygroseal valve has a semi-one way valve fitted already as standard, and will work on negative pressure systems.
No. Aladdin Autovents do not leak. They are guaranteed to operate for 3 years, and guaranteed leak-free for life. They contain a patented mechanical valve that positively closes when water gets to the internal mechanism of the valve. The Hygroseal™ range has a 5 year replacement guarantee.
Yes. Fitting the Autovent should reduce the need for corrosion inhibitors as all your radiators will be free of air, but we do recommend their use because corrosion leads to further gas collecting in the radiators. To allow inhibitors to be used ensure at least one radiator still has a manual vent plug fitted at the opposite end to an Autovent, as this will allow the inhibitor to be injected.
Leak-stop products can jam valves in certain circumstances. We do not recommend their use.
CDS (Superstores International) is not a lender and acts only as an introducer. The credit product is provided by Klarna Financial Services UK Limited (publ). Credit is only available to permanent UK residents aged 18 and over, depending on their status. Terms and conditions apply. Please note that Pay in 30 days and Pay in 3 instalments are regulated by the FCA.
By working with a variety of trusted Range Marketplace Partners, we’re able to offer our customers a wider selection of products.
When buying partner items like this one, your contract of sale will be with our Range Marketplace Partner instead of The Range.
To learn more about The Range Marketplace and our partners, visit our Range Marketplace page here.
Just contact us within 14 days of receiving your item and we'll authenticate the return.
Read our returns policy for more details
Return within
14 days
Return to store
No
Using returns label
No
Courier collection*
Yes
Return within
14 days
Return to store
No
Using returns label
No
Courier collection*
Yes
Return within
One year
Return to store
No
Using returns label
No
Courier collection*
Yes
*There may be a charge for the collection of your goods. You will be reimbursed the value of this charge if the returned goods are faulty.
By working with a variety of trusted Range Marketplace Partners, we’re able to offer our customers a wider selection of products.
When buying partner items like this one, your contract of sale will be with our Range Marketplace Partner instead of us.
To learn more about The Range Marketplace and our partners, visit our Range Marketplace page here
Made to Order products are those that we make especially for you and so can take a little longer to arrive. They are also excluded from our standard cooling off and change of mind policies. It takes 48 hours for us to process your order before we begin to make your product for you. After this time all Made to Order products are non-returnable and cannot be cancelled. To ensure your order goes smoothly and you are happy with your Made to Order product, please check the following:
Please check our Made To Order terms and conditions